An NAD-dependent enzymatic sensor with biofuel cell power source system for non-invasive monitoring of lactate in sweat was designed, developed, and tested. The sensor component, based on lactate dehydrogenase, showed linear current response with increasing lactate concentrations with limits of detection from 5 to 100 mM lactate and sensitivity of 0.2 µA.mM in the presence of target analyte. In addition to the sensor patch a power source was also designed, developed and tested. The power source was a biofuel cell designed to oxidize glucose via glucose oxidase. The biofuel cell showed excellent performance, achieving over 80 mA at 0.4 V (16 mW) in a footprint of 3.5 × 3.5 × 0.7 cm. Furthermore, in order to couple the sensor to the power source, system electronic components were designed and fabricated. These consisted of an energy harvester (EH) and a micropotentiostat (MP). The EH was employed for harvesting power provided by the biofuel cell as well as up-converting the voltage to 3.0 V needed for the operation of the MP. The sensor was attached to MP for chronoamperometric detection of lactate. The Sensor Patch System was demonstrated under laboratory conditions.

This study details the use of printing and other additive processes to fabricate a novel amperometric glucose sensor. The sensor was fabricated using a Au coated 12.7 μm thick polyimide substrate as a starting material, where micro-contact printing, electrochemical plating, chloridization, electrohydrodynamic jet (e-jet) printing, and spin coating were used to pattern, deposit, chloridize, print, and coat functional materials, respectively. We have found that e-jet printing was effective for the deposition and patterning of glucose oxidase inks with lateral feature sizes between ~5 to 1000 μm in width, and that the glucose oxidase was still active after printing. The thickness of the permselective layer was optimized to obtain a linear response for glucose concentrations up to 32 mM and no response to acetaminophen, a common interfering compound, was observed. The use of such thin polyimide substrates allow wrapping of the sensors around catheters with high radius of curvature ~250 μm, where additive and microfabrication methods may allow significant cost reductions.

In this paper, we attempt to understand the physico-chemical changes that occur in devices during device "burn-in". We discuss the use of low frequency dielectric spectroscopy to detect, characterize and monitor changes in electrical defects present in the dielectrics of through silicon vias (TSV) for three dimensional (3D) interconnected integrated circuit devices, as the devices are subjected to fluctuating thermal loads. The observed changes in the electrical characteristics of the interconnects were traceable to changes in the chemistry of the isolation dielectric used in the TSV construction. The observed changes provide phenomenological insights into the practice of burn-in. The data also suggest that these "chemical defects" inherent in the 'as-manufactured' products may be responsible for some of the unexplained early reliability failures observed in TSV enabled 3D devices.

In the fifteen years following the discovery of single-walled carbon nanotube (SWCNT) photoluminescence, investigators have made significant progress in their understanding of the phenomenon and towards the development of applications. The intrinsic potential of semiconducting carbon nanotubes - a family of bright, photostable near infrared (NIR) fluorophores (900-2100 nm) with tunable properties, has motivated their use as optical probes and sensors. In this perspective, we highlight the advances made in the synthesis, processing, modification, separation, and metrology of carbon nanotubes in the context of applications of their photoluminescence.

In this paper, we discuss the use of broadband microwaves (MW) to characterize the thermal stability of organic and hybrid silicon-organic thin films meant for insulation applications in micro- and nanoelectronic devices. We take advantage of MW propagation characteristics to extract and examine the relationships between electrical properties and the chemistry of prototypical low-k materials. The impact of thermal anneal at modest temperatures is examined to shed light on the thermal-induced performance and reliability changes within the dielectric films. These changes are then correlated with the chemical changes in the films, and could provide basis for rational selection of organic dielectrics for integrated devices.

Traditional metrology has been unable to adequately address the reliability needs of emerging integrated circuits at the nano scale; thus, new metrology and techniques are needed. In this paper, we use microwave propagation characteristics (insertion loss and dispersion) to study the atmospheric interconnect corrosion under accelerated stress conditions. The results presented in this work indicate that the corrosion resilience of the test device is limited by the thermal aging of the passivation layer.

A practical nanofabrication process is detailed here for the generation of black GaAs. Discontinuous thin films of Au nanoparticles are electrodeposited onto GaAs substrates to catalyze site-specific etching in a solution of KMnO and HF according to the metal-assisted chemical etching mechanism. This provides a solution-based and lithography-free method for fabricating sub-wavelength nanostructure arrays that exhibit solar-weighted reflectance approaching 4 %. This two-step benchtop process can be entirely performed at room-temperature without lithographic patterning or vacuum instrumentation, providing an alternative high-throughput nanotexturing approach for thin-film photovoltaics applications.